Home
Products
Face Drivers
Mechanical Face Drivers

Mechanical Face Drivers

Type 40 / Driving Diameter Range: 0.32 – 0.67 Inch

The Type 40 Series allows a driving diameter of 0.32″ to 0.67″. The driving pins move independently to allow a five-degree pitch of the end face of the work-piece. The mechanical compensation and lock down center point allow a constant length to be held from center to the taper. The Type 40 Series is available in 3, 4,and 5 morse taper designs as well as a flange mount. Chuck mounting can be achieved as described in the mounting procedures. View Catalog Page

Type 41 / Driving Diameter Range: 0.24 – 0.75 Inch

The Type 41 Series allows a driving diameter of 0.24″ to 0.75″. The driving pins move independently to allow a five-degree pitch of the end face of the work-piece. The mechanical compensation and lock down center point allow a constant length to be held from center to the taper. The Type 41 Series is available in 3, 4,and 5 morse taper designs as well as a flange mount. Chuck mounting can be achieved as described in the mounting procedures. View Catalog Page

Type 42 / Driving Diameter Range: 0.43 – 0.79 Inch

The Type 42 Series allows a driving diameter of 0.43″ to 0.79″. The driving pins move independently to allow a five-degree pitch of the end face of the work-piece. The mechanical compensation and lock down center point allow a constant length to be held from center to the taper. The Type 42 Series is available in 3, 4,and 5 morse taper designs as well as a flange mount. Chuck mounting can be achieved as described in the mounting procedures. View Catalog Page

Type 43 / Driving Diameter Range: 0.51 – 1.02 Inch

The Type 43 Series allows a driving diameter of 0.51″ to 1.02″. The driving pins move independently to allow a five-degree pitch of the end face of the work-piece. The mechanical compensation and lock down center point allow a constant length to be held from center to the taper. The Type 43 Series is available in 3, 4,and 5 morse taper designs as well as a flange mount. Chuck mounting can be achieved as described in the mounting procedures. View Catalog Page

Type 44 / Driving Diameter Range: 1.02 – 1.42 Inch

The Type 44 Series allows a driving diameter of 1.02″ to 1.42″. The driving pins move independently to allow a five-degree pitch of the end face of the work-piece. The mechanical compensation and lock down center point allow a constant length to be held from center to the taper. The Type 44 Series is available in 4 and 5 morse taper designs as well as a flange mount. Chuck mounting can be achieved as described in the mounting procedures. View Catalog Page

Type 45 / Driving Diameter Range: 1.34 – 1.73 Inch

The Type 45 Series allows a driving diameter of 1.34″ to 1.73″. The driving pins move independently to allow a five-degree pitch of the end face of the work-piece. The mechanical compensation and lock down center point allow a constant length to be held from center to the taper. The Type 45 Series is available in 4 and 5 morse taper designs as well as a flange mount. Chuck mounting can be achieved as described in the mounting procedures. View Catalog Page

Type 46 / Driving Diameter Range: 1.14 – 1.93 Inch

The Type 46 Series allows a driving diameter of 1.14″ to 1.93″. The driving pins move independently to allow a five-degree pitch of the end face of the work-piece. The mechanical compensation and lock down center point allow a constant length to be held from center to the taper. The Type 46 Series is available in a flange mount. Chuck mounting can be achieved as described in the mounting procedures. View Catalog Page

Type 47 / Driving Diameter Range: 1.54 – 2.32 Inch

The Type 47 Series allows a driving diameter of 1.54″ to 2.32″. The driving pins move independently to allow a five-degree pitch of the end face of the work-piece. The mechanical compensation and lock down center point allow a constant length to be held from center to the taper. The Type 47 Series is available in 5 and 6 morse taper designs as well as a flange mount. Chuck mounting can be achieved as described in the mounting procedures. View Catalog Page

Type 48 / Driving Diameter Range: 1.93 – 2.72 Inch

The Type 48 Series allows a driving diameter of 1.93″ to 2.72″. The driving pins move independently to allow a five-degree pitch of the end face of the work-piece. The mechanical compensation and lock down center point allow a constant length to be held from center to the taper. The Type 48 Series is available in a flange mount. Chuck mounting can be achieved as described in the mounting procedures. View Catalog Page

Type 49 / Driving Diameter Range: 2.72 – 3.90 Inch

The Type 49 Series allows a driving diameter of 2.72″ to 3.90″. The driving pins move independently to allow a five-degree pitch of the end face of the work-piece. The mechanical compensation and lock down center point allow a constant length to be held from center to the taper. The Type 49 Series is available in a flange mount. Chuck mounting can be achieved as described in the mounting procedures. View Catalog Page

Type 50 / Driving Diameter Range: 4.33 – 5.51 Inch

The Type 50 Series allows a driving diameter of 4.33″ to 5.51″. The driving pins move independently to allow a five-degree pitch of the end face of the work-piece. The mechanical compensation and lock down center point allow a constant length to be held from center to the taper. The Type 50 Series is available in a flange mount. Chuck mounting can be achieved as described in the mounting procedures. View Catalog Page

Products

Services

Technical Support